У зв'язку зі святкуванням Нового Року ми працюємо за наступним графіком: • з 31.12.24(Вт) по 02.01.25(Чт) не працюємо • з 03.01.25(Пт) працюємо в звичайному режимі.
Інтерет-магазин приймає замовлення цілодобово 24/7 !
Web Speech API is not supported by this browser. Install Google Chrome.
Voice input also works in Safari, Yandex, as well as mobile browsers Huawei, Opera and Samsung..
Conductive copper-based protective coating with silver additive. It is used as a shielding coating for protection against electromagnetic interference (EMI) and electrostatic discharge (ESD), for the manufacture of contact connectors. Spray 200 ml.
EMILAC is a conductive varnish based on fine copper powder with the addition of silver.
Adequate shielding effect of the varnish is achieved by applying a thinner layer in comparison with traditional means - for example, copper foil. For a good result, a layer of EMILAC with a thickness of only 40-75 microns is sufficient. At the same time, applying varnish is much more technological than installing foil screens.
Conductive varnish has high adhesion to plastic, glass, metals and other materials.
Copper varnish EMILAC Cramolin aerosol is easy to use, quick-drying.
Retains its properties (conductivity) under difficult operating conditions, in a wide range of temperature and humidity.
Properties:
application method: dipping, spraying
color: copper
filler: silver plated copper
lacquer base: polyacrylate resin
density: 1.04 g/cm³
interlayer drying time: at room temperature after 10 min. dries to dryness
complete drying time: 24 hours at room temperature
oven drying time: ~ 30 minutes at 60-70°C (after pre-drying at room temperature for 10 minutes)
surface resistance: <0.5 Ω/mm 2 (with a film thickness of 25 μm)
Attenuation: (ASTM ES 7-83): 60 - 65 dB (at 50 μm film thickness)
coverage area: 4 m 2 /l (with a film thickness of 50 microns)
recommended coating thickness: 40 - 75 microns
operating temperature range: -40°С -+95°С
Purpose
protection against electromagnetic interference (EMI) and electrostatic discharge (ESD)
use in electronic laboratories to protect data processing devices, measuring technology and other equipment
car electronics service
production of contact connectors
shielding of plastic cases, boxes and casings
corrosion protection for aluminum enclosures
Directions for use
The surface to be protected must be free from dirt, grease, wax, silicone. Shake the can well before use. Apply the aerosol by spraying from a distance of approximately 30 cm, otherwise drips may form on the surface. The clogged nozzle is flushed with solvent.
The varnish used for dip coating can also be used for spray application when thinned with THINNER FOR EMILAC in a ratio of 1: 4. The varnish must be thoroughly mixed so that the pigment is evenly distributed throughout the volume.
Leave your feedback or ask a question
Only this product is discussed here. Off topic comments will be deleted! Please follow the Commenting Rules.
The data presented in the product description are for reference only and may differ from those indicated by the manufacturer.
To carry out technical calculations and obtain the exact parameters of the goods, use the datasheets from the manufacturer's website.
If you need additional information, or you found an error in the description, or have other questions about this product, then our manager will help you: Ярослав
unknown
![Conductive copper varnish EMILAC 200ml [spray]](/files/pic/kontchim/019971-s.jpg)
Описание на сайте производителя (на английском)
Техническое описание
![Conductive copper varnish EMILAC 200ml [spray]](/files/pic/kontchim/019971.jpg)
The data presented in the product description are for reference only and may differ from those indicated by the manufacturer.
